![]() ![]() ![]() I've only just got this kit which was sent direct from Hong Kong to me. I'm beginning to wonder if it isn't the XTAG2. It also seems very flaky at picking up the XTAG2 - sometimes it says it can't find a device even when it's just run fine. This is similar to what I was seeing yesterday when I was trying to get XScope going - XDE kept hanging and then trying to melt my Macbook. It seems to hang xgdb - it goes totally unresponsive. Xrun -xscope-file "test.xmt" -xscope-limit 1000 -verbose xscopetest.xe Transfer rate: 123 KB/sec, 1382 bytes/write.Įnable xscope on core 1 at address 0x15028 text._call_exitprocs_impl, size 0x2 lma 0x14d68 Transfer rate: 120 KB/sec, 1400 bytes/write.Įnable xscope on core 0 at address 0x1513c text._call_exitprocs_impl, size 0x2 lma 0x14e60 Transfer rate: 90 KB/sec, 130 bytes/write.Įnable xscope on core 1 at address 0x10284 The message "First stage multi-node boot failed, please check XN file and Xmos link connectivity" is suggesting there is something not right with link configuration.īash-3.2$ xrun -xscope-file "test.xmt" -xscope-limit 1000 -verbose xscopetest.xe Would you be able to attach the XN file you are using, XN file, but I've done exactly what's specified in the tools manual so I'm confused. Transfer rate: 93 KB/sec, 134 bytes/write.Įnable xscope on core 0 at address 0x10298įirst stage multi-node boot failed, please check XN file and Xmos link connectivityīut all it does is create an empty xmt file with this in it :Ĭan anybody point me in the direction of whatever stupid mistake I'm making? The error suggests a problem with the. 5) Can I connect the XScope to the computer using the USB for firmware updates Yes, the device has a USB bootloader. A UART to USB cable is required for hardware 1.4 and 1.5. Xrun -xscope-file "test.xmt" -xscope-limit 1000 -verbose XscopeTest_Debug.xe 4) Can I connect the XScope to the computer to control the oscilloscope and get the data Yes, you can use the XScopes PC Interface. With the intention of trying to just prove it will create something. Description Xscope sits in-between an X11 client and an X11 server and prints the contents of each request, reply, error, or event that is communicated between them. XSCOPE_CONTINUOUS, "Microphone Right", XSCOPE_UINT, "mV" ) GPIO Expansion For the eccentric makers among you, the ProtoLab comes with GPIO expansion pins pre-assembled – so you can add another board on top of this one for some really hardcore prototyping.XSCOPE_CONTINUOUS, "Microphone Left", XSCOPE_UINT, "mV", globcode, size 0x22 lma 0x1024c Loading section. ![]() text, size 0x24c lma 0x10000 Loading section. If the rare white silkscreen doesn’t catch your attention, the features probably will. xrun -xscope-file 'test.xmt' -xscope-limit 1000 -verbose XscopeTestDebug.xe 0x00010000 in main Loading setup image to XCore 0 Loading section. You sir, would be most incorrect with your wild assumptions! The stylish board in fact packs a lot of functionality in a subtle, tidy and low profile package. Without close inspection, you could be fooled into thinking it was just a perfboard-style breakout board with some terminal blocks around the side. Happy days! The ProtoLab is quite a deceiving little number. Research at the BRIC is collaborative and interdisciplinary by design, encouraging sharing of ideas and promoting new approaches to. The Directors office oversees the daily operations of the BRIC as well as multiple core research facilities. Lucky for me, the board comes pre-assembled, saving me a few burnt fingers. Baylor University’s ProtoLAB is a new, full-service prototyping facility located at the Baylor BRIC. It had to be mine! Let’s take a look at the board and its features… I received my ProtoLab today – a Tuesday – a work day where I’m a lot less likely to have the motivation to get the soldering iron out. It’s a bit of a fresh approach compared to some of the other offerings on the market, and its classy white ‘iPod-era’ colours caught my eye on eBay. The company’s decision to buy 3D Hubs has. This week another package came through the letterbox – a ProtoLab GPIO breakout board from AlienSpec. In its first quarter financials, Protolabs reported 116 million in consolidated revenue, 10 more than the 105 million generated during Q4 2020. With any hobby I take an interest in, I always seem to end up buying masses of accessories, usually before I’ve even acquire the skills to use them! I’m a little further along on my Pi journey now, so I think these impulse purchases are becoming more relevant with time (wife…are you reading this?). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |